Anastasia EdryPlanning And CommunicationPurdue University

Jackalope Animatronic Build





The Story

In the Mystic Cabin, creatures are afoot. Guests embark on a typical tour through a seemingly normal “Museum of Odditites” only to have it go awry and end in a high speed chase after one of the exhibits itself! Throughout the queue of the ride itself, as well as the in show decor, there will be many depictions of oddities, such as wet specimens or large statues. When brainstorming for the project, the most “classic” oddity I could imagine, was that of the jackalope, a rabbit with antlers. With the theming decided upon for the project, a jackalope wall mount would fit the overall aesthetic as well as provide visual interest through the animatronic aspect of it. 





The Plan

Modify a consumer-grade Mr. Christmas Animated reindeer into a singing jackalope to align with the cryptid, haunted, roadside attraction theming of the overall project. 




Original Reindeer
Sketch of Modification

The Process

In order to transform the reindeer, it first had to be dismantled. Using the screws and connection points already located on the reindeer made dismantling easy.




Lighting wire was disconnected for removal.
It was necessary to unscrew and detatch wires that held the antler armature wire in place.
The stuffing and skin of the reindeer was remved, being carful not to damage the motion sensor in the nose.
The skeleton left post dismantling.
Side angle of the skeleton.

Adding New Skin

Once the original skin of the animatronic was removed, I began patterning for the new rabbit skin. I made an initial mock up out of scrap cotton muslin, and then traced it onto the faux fur. The piece was then sewn on a machine, and attached to the base of the animatronic. After which, it was stuffed to give it a plush look. For the face portion, a larger circle of faux fur was cut out and gathered to make a dome shape, this was then attached to the neck and stuffed. Once the stuffing was complete, it was shaped via strategic hand sewing. Finally, ears were added that I patterned on paper before cutting out of the fabric. The ears have artmature wire through them, so they are poseable. 




Initial muslin mockup.
Traced onto the reverse side of the faux fur.
The open neck. 

3D Modeling

The jackalope needed eyes as well as antlers to complete the look. I utlized Rhino as my modeling software of choice, and modeled both the eyes, antlers, and teeth. These were then 3D printed on my Qidi X-Plus printer. Once printed, the pieces were cleaned and painted.  They could then be adhered onto the jackalope, and the lights were restrung around the new antlers.




Rendered model of the antlers.
Rendered model of the eyes and teeth. 
3D printed antlers. 

Completion

The jackalope was then mounted onto a wooden plaque. One the back of the plaque I attached a frame hanger, and the animatronic is attached to the plaque via Command Hook and Loop Tape. I chose this so that it could be removed to change batteries and turn it on and off. She still sings Christmas songs!




Hook and Loop Tape attached to the back of the animatronic.
Picture hanger nailed to the back of the plaque. 
Rendered model of the antlers.
Video of one of the possible songs.


Budget


Item


Animated Reindeer

1 Yard Faux Fur

1 yard cotton batting

White 3D Printer Filament

Hot Glue Sticks 

Picture Hanger

Wooden Plaque

Hook and Loop Tape Command Strips

PolyFil


Materials total


Additional Equiptment Already Owned
Used Qidi 3D Printer

Rhino 3D

Hot Glue Gun

Singer 503a Sewing Machine
Cost

53.44

10

3

12.99

10

2.99

11.25

5.99

5


114.66


Estimated Cost
100

995

20

75




Jackalope Animatronic